干燥機
特點
與原料接觸的地方全部為不銹鋼材質制成
配備入料口蓋，方便吸料機的安裝
采用“熱風下吹式，空氣旋風排氣”的原理，保證干燥效果均勻統一
選購配備七天型定時器，用于自動定時開關機
可調式過熱安全保護裝置
標準外接式絕緣主電源
符合CE安全標準的電路設計
Stee Hopper Dryer
Features
All parts contacting with raw material is made of stainless steel
A material nl liet cover is equipped , which is easy for installation of suction machine
With principles of Hot Air Down Blowing and Whirlwind Air exhausting h , te drying effect is ensured as even and uniform
A7-day timer is optional for automatic timing switch
Adjustable overheat safeguard devices
Standard external isulated master power supply
Circuit design meeting CE safety standards
選擇加裝配件
卸料座，磁力架，吸料盒，熱風回收系統，A型腳架，L型腳架，斷料式吸料箱
Optional Accessories
1:unloading seat 2: magnetic stand 3: suction box 4: hot air recycling system 5: A-type tripod 6: L type foot stand 7: broken material suction box
箱型干燥機
特點
采用電子溫度控制，提供精密的均勻烘干效果
高溫密封開門以保持一致的溫度和降低電力的損耗
不銹鋼盤可以排除在烘干過程中所造成原料污染的弊端
方便保養的設計
可調式高溫保護器
附安培表
24小時定時裝置
可調式空氣開門
馬達過載保護
主電源開關
Adopt electronic temperature control
Provide precise dry-up function High-temperature fully-closed door can ensure constant temperature and reduce electrical consumption
Stainless steel can exclude the disadv-antages of the raw material contamination
Convenient design and maintenance
Adjustable temperature protector
The accessory includes ammeter
24H timer device
Adjustable air valve
Motor over-load protection
Power switch
1.循環馬達 Recycle motor
2.多翼式風輪 Blower
3.風室 Air room
4.入風口 Air inlet
5.不銹鋼托盤 Stainless trays
6.耐高溫保溫巖棉 Asbestos cloth
7.烤漆鋼板 Paint coating steel sheets
8.片狀間隔板 Plate spacer
9.出風口 Air outlet
10.電熱管 Heater
工作原理
箱型干燥機中有可移動的盤子，需干燥的原料放在盤子內，運行時風車迫使空氣通過電熱管，再穿過有很多的小孔隔墻，并均勻吹進原料，當原料均勻烘干后，潮濕的空氣從另一道墻口排出
Working Principle
Place material on the movable trays; start the switch on power and machine starts to operate , strong wind wheel activated will blow air from the air inlet into the electric heating tube , hot air goes through the pored separated wall , and blows evenly on the material , moisture will be expelled by the dehumidification blower on the top . Moisture is expelled and material is dried through repeated process
適用范圍
箱型干燥機適用于所有種類的聚合物材料烘干，并能同時烘干不同材料，非常適用于量多樣性的原料，或試模時使用，也可用于農產品（花粉、蒜頭、茶葉）或電子，電機，電渡，制藥，烤漆，印刷等多行業相關產品的預熱或干燥處理
Application scope
The dry-up machine can be applied for the dry-up of all kinds of polymers . It also can dry up different kinds of materials . It is suitable for the dry-up of little and different materials e .g .powder , garlic and tea etc . It can be used for the dry-up/warm-up operation for the products in the fields of electronic , electric machinery , galvanization , pharmacy , baked enamel and printing industries
除濕干燥機
什么是蜂巢式陶瓷除濕轉輪
蜂巢式陶瓷除濕轉輪是以陶瓷羅維為基材形成蜂巢轉輪，然后利用特殊化學合成兩段結晶方法，把吸濕劑硅膠和分子篩均勻結晶在陶瓷羅維轉輪上，使其具有極強吸濕能力，這種結構的轉輪在運行時不會產生粉末，并且使用壽命大大延長，潮濕的空氣通過蜂巢式除濕轉輪中無數微孔（吸濕劑）后，濕氣被有效的吸收，經除濕轉輪過濾分離出來的空氣被撤底除濕后成為超低露點的干燥空氣，再生也是在同樣的原理下進行的，只是通過蜂巢除濕轉輪（吸濕劑）的方向相反
Dehumidifier Series
What’s the cellular ceramic desiccant wheel?
Desiccant wheel cellular ceramic substrate is formed of ceramic fiber honeycomb wheels , then the use of special methods of chemical synthesis of two crystals , the hygroscopic agent silica gel and molecular sieve crystals evenly on the wheel in the ceramic fiber , it has strong moisture absorption capacity . The structure of the wheel will not have powder in the run-time and significantly longer service life . Moist air through the desiccant wheel in numerous cellular micro (hygroscopic agent ), the moisture is effectively absorbed by the desiccant wheel out of the air filter was completely isolated after a low dew point dehumidification dry air . Regeneration is carried out under the same principle , only through the honeycomb desiccant wheel (hygroscopic agent )in the opposite direction
在什么情況下使用除濕機
塑料制品成型不良，多數源自除濕干燥不良，美國塑料協會建讓成型前的塑料必須干燥到0.02%以下的含水率，透明度不佳，濾道粘住，毛邊，氣泡，封條，流痕，開裂，尺寸穩定性不佳，產生內壓力，產品物性強度不足等缺點，其多數不良原因，在于成型前塑料未被充分除濕干燥所致，尤其高浸水性塑料如：PET，PBT，PA，PC等更需要超低露點DEW POINT-40℃干燥設備
Under what circumstances to use dehumidifier?
Plastic molding bad , most from dehumidification drying bad . American Plastics Association recommends that pre-molded plastic must be dried to a moisture content below 0.02% , poor transparency , runner stick , flash bubbles ,draw bar ,flow marks ,cracking , poor dimensional stability ,resulting in stress, product properties such as strength , weaknesses , most of its bad reason ,is mot fully formed before plastic due to dehumidification drying Particularly high , such as immersion of plastic : PET ,PBT ,PA , PC , etc. need low dew point Dew point -40℃drying equipment
除濕干燥機選購配件
24H預約定時器
可以設置定時開機和定時關機
露點偵測顯示器，可選擇：A隨機安裝式B手提式
濾油器
當干燥原料里含有塑化劑時須使用濾油器
旋風集塵器
適有于粉塵較多的PET除塵系統
紅色雙層硅膠風管
觸控式人機界面
采用PLC控制搭配人機界面
Optional Accessories
24H reservation timer ( you can set start time and time off )
Dew point detection display ( Optional : a .b . Portable random mount )
Oil filter (When the dried material contains plasticizer oil filter to be used )
Cyclone dust collector : with photos (PET more suitable for dust removal system )
Red double-decker silicone duct
Touch man-machine interface : with photos (PLC control with man-machine interface )
除濕干燥送料三機一體
ADS系列除濕干燥送料三機一體，是結合塑膠行業的實際情況而研發出來的新產品，該機采用獨有的多段式蜂巢轉輪，不銹鋼雙層下吹式保溫料斗，臺灣產送料風機，德國西門子，日本歐姆龍，日本三菱等名牌電器零件，因該機集中除濕，烘干，送料為三機一體，在塑膠生產中具有供料快速簡單，結構緊湊，堅固耐用等優點，讓您在塑膠成型中，確保品質及充分展現塑料完美的物性，進而提升競爭實力
Desiccant Feeding Three In One
ADS series desiccant feeding Three in one , a combination of the actual situation of the plastics industry developed new products , The machine uses a unique multi-stage honeycomb wheels , stainless steel double blow insulation under the hopper , feeding fans from Taiwan , Siemens , Omron , Mitsubishi and other brands of electrical components . Concentration due to aircraft dehumidification , drying feeding on to three machines in the production of a plastic material for quick and simple , compact , rugged , etc ., let you in the plastic molding , plastic to ensure perfect quality and full of physical properties and thus enhance competitiveness
特點
集二段送料，除濕，干燥功能為一體，但各項控制均可獨立操作
日本進口微電腦P.I.D自動調節，可自動控制整機運行
24小時自動定時器可預定時間開機關機（選購）
特有下吹式雙層料斗設計，防止熱能散失，節省能源
密閉回路送料系統，避免干燥后的原料因接觸外界空氣再受潮
結構緊湊，占地少，移動方便
故障自動保護功能，故障率低，維護方便
本機適用于吸濕性較強的工程塑膠原料如：PA，PC，PBT，PET等
Features
Set Sec feeding , dehumidification , drying function as a whole , but the control can operate independently
Japan imports Microprocessor P.I.D automatic control , automatic control of machine operation
24-hour automatic timer to turn off the scheduled time (Choose)
Double Blow unique hopper design , to prevent heat loss and save energy
Closed loop feeding system , to avoid drying of raw materials due to exposure to outside air and then wet
Compact , small footprint , easy to move
Fault protection , low failure rate , easy maintenance
The machine is suitable for highly hygroscopic materials such as engineering plastics : PA , PC ,PBT ,PET and so on
恩必信客服
銷售熱線 韓攀 13794992579
銷售熱線 韓攀 13794992579